[Kasbert]

Thanks for the information.
I am using Dropad A8X (firmware 20110705) and Elgato DTT (=Hauppauge Nova-T Stick, Id 2040:7050). dvb-core is built into kernel, I think, since it shows in /proc/devices from the beginning. I used dvb-usb-dib0700-1.20.fw and the following modules :

<br />
insmod dvb-usb.ko force_pid_filter_usage=1<br />
insmod dvb-pll.ko <br />
insmod dibx000_common.ko <br />
insmod dib0070.ko <br />
insmod dib3000mc.ko <br />
insmod dib7000m.ko <br />
insmod dib7000p.ko <br />
insmod dib8000.ko <br />
insmod dvb-usb-dib0700.ko <br />

However dmesg says that "This USB2.0 device cannot be run on a USB1.1 port". I tried also without force_pid_filter_usage=1. I guess I am out of luck.

<br />
<6>dib0700: loaded with support for 13 different device-types<br />
<6>dvb-usb: found a 'Hauppauge Nova-T Stick' in cold state, will try to load a firmware<br />
<6>usb 1-1: firmware: requesting dvb-usb-dib0700-1.20.fw<br />
<3>init: untracked pid 3019 exited<br />
<6>dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw'<br />
<6>dib0700: firmware started successfully.<br />
<6>dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state.<br />
<3>dvb-usb: This USB2.0 device cannot be run on a USB1.1 port. (it lacks a hardware PID filter)<br />
<6>dvb-usb: Hauppauge Nova-T Stick error while loading driver (-19)<br />
<6>usbcore: registered new interface driver dvb_usb_dib0700<br />

 

[chase]

Thanks for the information.
I am using Dropad A8X (firmware 20110705) and Elgato DTT (=Hauppauge Nova-T Stick, Id 2040:7050). dvb-core is built into kernel, I think, since it shows in /proc/devices from the beginning. I used dvb-usb-dib0700-1.20.fw and the following modules :

<br />
insmod dvb-usb.ko force_pid_filter_usage=1<br />
insmod dvb-pll.ko <br />
insmod dibx000_common.ko <br />
insmod dib0070.ko <br />
insmod dib3000mc.ko <br />
insmod dib7000m.ko <br />
insmod dib7000p.ko <br />
insmod dib8000.ko <br />
insmod dvb-usb-dib0700.ko <br />

However dmesg says that "This USB2.0 device cannot be run on a USB1.1 port". I tried also without force_pid_filter_usage=1. I guess I am out of luck.

<br />
<6>dib0700: loaded with support for 13 different device-types<br />
<6>dvb-usb: found a 'Hauppauge Nova-T Stick' in cold state, will try to load a firmware<br />
<6>usb 1-1: firmware: requesting dvb-usb-dib0700-1.20.fw<br />
<3>init: untracked pid 3019 exited<br />
<6>dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.20.fw'<br />
<6>dib0700: firmware started successfully.<br />
<6>dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state.<br />
<3>dvb-usb: This USB2.0 device cannot be run on a USB1.1 port. (it lacks a hardware PID filter)<br />
<6>dvb-usb: Hauppauge Nova-T Stick error while loading driver (-19)<br />
<6>usbcore: registered new interface driver dvb_usb_dib0700<br />

i had this message once or twice. for some reason my port was detected as 1.1. when it happened, i just removed the dongle and inserted again. nothing more...

 

[Kasbert]

i had this message once or twice. for some reason my port was detected as 1.1. when it happened, i just removed the dongle and inserted again. nothing more...

I think Dropad A8X really has a USB 1.1 host port. The other USB port may be 2.0 one, but I don't think it can be used for this. Maybe I invest some 10 or 20 EUR to get a DVB stick with pid filtering.

 

[denys]

Lubo, you have made a great job! From your work I see that you have a good knowledge in Android! Am I right? If yes, can you assist me in firmware support of UART GPS module? Think this will be very useful in our tablet...

 

[Omega5]

i completely install DVB AF903x on my tablet
but i have a little problem on audio codec
when i see a dvb-t channel the audio will be stretched (distorted) on VPlayer (android)

the mumudvb configured the channel video as MPEG-4(AVC) and audio as AAC-LATM automaticaly
i didn't know what is the problem and how can i solve it

 

[msux]

my stick is "LiteOn USB DVB-T TV Tuner USB2.0/USB1.1 dvb-usb-dibusb-6.0.0.8.fw MT2060 silicon tuner"

after:
insmod /sdcard/dvb-core.ko
insmod /sdcard/dvb-usb.ko force_pid_filter_usage=1
insmod /sdcard/dvb-pll.ko
insmod /sdcard/dibx000-common.ko
insmod /sdcard/dib3000mc.ko
insmod /sdcard/mt2060.ko
insmod /sdcard/dvb-usb-dibusb-mc.ko
insmod /sdcard/dvb-usb-dibusb-common.ko

my stick's blue light is on

use livetv to scan channel

got

tune to: QAM_AUTO f = 634000 kHz I999B8C999D999T999G999Y999
(time: 08:34) Info: PAT filter timeout
Info: SDT(actual) filter timeout
Info: NIT(actual) filter timeout
.
.
.(0 service stored)

any help!

 

[motylu]

Hi,
I have the Archos 70 IT tablet running od Android 2.2 Froyo and USB tuner AverTV Hybrid Volar HX A827. I would like to watching DVB-T using mumudvb (as desribed here), but I can´t find kernel modules "h826d.ko" and "averusbh826d.ko" for tuner to download. Does anyone have these kernels? Thank a lot

 

[motylu]

Hi,
I have the Archos 70 IT tablet running od Android 2.2 Froyo and USB tuner AverTV Hybrid Volar HX A827. I would like to watching DVB-T using mumudvb (as desribed here), but I can´t find kernel modules "h826d.ko" and "averusbh826d.ko" for tuner to download. Does anyone have these kernels? Thank a lot

Today, I installed drivers from Avermedia to Ubuntu 9.10. So I have both of these kernel modules, but I am not possible to put its in my Android tablet. How can I compile these kernel modules for Linux to kernel modules for Android?

I really want to play DVB-T in my tablet - in school, home etc. Thank you very much !!!

 

[vadiator]

Hi!)
I need modules PCTV 340e SE, can you crosscompile the drivers for me please?
drv lunix
thank's

 

[freesailor]

Hi, when I try to run mumudvb I get "not found" message, but mumudvb is really ther in system/xbin with all permissions.

 

[Maindude]

Can anyone post complete zipfile and gscript for a dvb t Realtek 2838.

Thanks

 

[cvsandeep]

Hi,

How to use composite video in android using wintv-HVR 950q

Thanks

 

[jarazz]

Hi LUBO
Could You help me to install Pinnacle PCTV 340e ??
I have tab with Cortex ARM 10 - Android 4.0.3, kernel 3.0.8+
I think that drivers & firmware are here http://www.kernellabs.com/blog/?p=1247
Best regards

 

[stefki87]

Hi all, the forum is great.

I have problem with my Linux PC and mumudvb

This is my hardware info:
Ubuntu 10.10
Bus 001 Device 002: ID 15a4:9016 Afatech Technologies, Inc. AF9015 DVB-T USB2.0 stick
mumudvb Version 1.6

I can't stream the channels from my server. This is my config for mumudvb

freq=554
dont_send_sdt=1
multicast=0
unicast=1
port_http=1234
ip_http=0.0.0.0
sap=1
autoconfiguration=0
ip=192.168.1.138
name=MTV1
pids=1012

These are the channels scanned with "w_scan"
MTV1;NETTV:554000:I999B8C999D999M999T999G999Y999:T:27500:1011:1012=mac:0:0:1:0:0:0
MTV2;NETTV:554000:I999B8C999D999M999T999G999Y999:T:27500:1021:1022=mac:0:0:2:0:0:0
MTV3;NETTV:554000:I999B8C999D999M999T999G999Y999:T:27500:1031:1032=mac,1033=alb:0:0:3:0:0:0

These are the same channels scanned with "scan"

MTV1:554000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE:1011:1012:1
MTV2:554000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE:1021:1022:2
MTV3:554000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE:1031:1032:3

And this is the log from mumudvb console

[email protected]:/var/bin# sudo mumudvb -c dvb-t.conf -s -t -vv -d
MuMuDVB Version 1.6
Latest version available from http://mumudvb.braice.net/

You decided not to send the SDT pid. This is a VLC workaround.
Config issue : unknow symbol : multicast

Config issue : unknow symbol : unicast

You have enabled the support for HTTP Unicast. This feature is quite youg, please report any bug/comment
Sap announces will be sent
Bad value for autoconfiguration, autoconfiguration will not be run
Streaming. Freq 554000
Using DVB card "Afatech AF9013 DVB-T"
tuning DVB-T to 554000000 Hz, Bandwidth: 8
polling....
Getting frontend event
FE_STATUS:
polling....
Getting frontend event
FE_STATUS:
FE_HAS_SIGNAL : found something above the noise level
FE_HAS_CARRIER : found a DVB signal
FE_HAS_VITERBI : FEC is stable
FE_HAS_SYNC : found sync bytes
FE_HAS_LOCK : everything's working...
Event: Frequency: 554000000
Bit error rate: 0
Signal strength: 28575
SNR: 120
FE_STATUS:
FE_HAS_SIGNAL : found something above the noise level
FE_HAS_CARRIER : found a DVB signal
FE_HAS_VITERBI : FEC is stable
FE_HAS_SYNC : found sync bytes
FE_HAS_LOCK : everything's working...
Card 0 tuned
The traffic will be shown every 10 seconds
Setting filter for PID 0
Setting filter for PID 1
Setting filter for PID 16
Setting filter for PID 17
Setting filter for PID 18
Setting filter for PID 20
Setting filter for PID 1012
Unicast : We open the Master http socket for address 0.0.0.0:1234
unicast : fds->pfdsnum : 2
Diffusion 1 channel
Channel number : 0, ip : 192.168.1.138:1234, name : "MTV1"
pids : 1012
Bit error rate: 145 Signal strength: 28575 SNR: 270
DEBUG : sap sending ip address : 0x0
DEBUG : SAP payload
v=0
o=MuMuDVB 356443 1 IN IP4 192.168.1.138
s=MTV1
c=IN IP4 192.168.1.138/2
t=0 0
a=tool:mumudvb-1.6
a=type:broadcast
m=video 1234 udp 33
DEBUG : end of SAP payload

Bit error rate: 224 Signal strength: 28575 SNR: 270
Bit error rate: 182 Signal strength: 28575 SNR: 270
Bit error rate: 77 Signal strength: 28125 SNR: 270
Bit error rate: 192 Signal strength: 28125 SNR: 270
Bit error rate: 28 Signal strength: 28575 SNR: 270
Traffic : 33.88 kB/s for channel "MTV1"
Bit error rate: 159 Signal strength: 28575 SNR: 270
Bit error rate: 70 Signal strength: 28575 SNR: 270
Unicast : New client
Unicast : New connection from 192.168.1.124:28178
Unicast : We create a client associated with the socket 15
Unicast : first client
Unicast : Number of clients : 1
Unicast : We've got a POLLHUP. Actual_fd 2 socket 15 we close the connection
Unicast : We close the connection
Unicast : We delete the client 192.168.1.124:28178, socket 15
Unicast : ---------------Before-------------
We see socket 15
Unicast : We delete the first client
Unicast : --------------- After -------------
Unicast : 0 client
Unicast : Number of clients : 0
Unicast : New client
Unicast : New connection from 192.168.1.124:28434
Unicast : We create a client associated with the socket 15
Unicast : first client
Unicast : Number of clients : 1
Unicast : New message for socket 15
Unicast : We received 20, buffer len 100 new buffer pos 20
Unicast : New message for socket 15
Unicast : We received 81, buffer len 200 new buffer pos 101
Unicast : End of HTTP request, we parse it
Unicast : Path not found i.e. 404
Unicast : We close the connection
Unicast : We delete the client 192.168.1.124:28434, socket 15
Unicast : ---------------Before-------------
We see socket 15
Unicast : We delete the first client
Unicast : --------------- After -------------
Unicast : 0 client
Unicast : Number of clients : 0
Unicast : New client
Unicast : New connection from 192.168.1.124:28690
Unicast : We create a client associated with the socket 15
Unicast : first client
Unicast : Number of clients : 1
Unicast : New message for socket 15
Unicast : We received 46, buffer len 100 new buffer pos 46
Unicast : New message for socket 15
Unicast : We received 100, buffer len 200 new buffer pos 146
Unicast : New message for socket 15
Unicast : We received 100, buffer len 300 new buffer pos 246
Unicast : New message for socket 15
Unicast : We received 31, buffer len 400 new buffer pos 277
Unicast : End of HTTP request, we parse it
Unicast : Path not found i.e. 404
Unicast : We close the connection
Unicast : We delete the client 192.168.1.124:28690, socket 15
Unicast : ---------------Before-------------
We see socket 15
Unicast : We delete the first client
Unicast : --------------- After -------------
Unicast : 0 client
Unicast : Number of clients : 0
Bit error rate: 240 Signal strength: 28575 SNR: 270
^C
End of streaming. We streamed during 0:00:20

On the client side I am using Windows XP pc with VLC player installed
http://192.168.1.138:1234/
Your input can't be opened:
VLC is unable to open the MRL 'http://192.168.1.138:1234'. Check the log for details.

 

[Varma]

Hi evrybody!

Great idea and well done Lubo!

I owe a Ainol Hero 10 and a DVB-T AF9015.
I was wondering to use the stuff you compiled when I realized.... maybe they are compiled just for this machine

The Ainol Hero has a AML8726-MX A9 cpu (if i'm not wrong); should I recompile all the pieces?

thank you very much

 

[hor13]

Help me!
I have dropad A8t with kernel 2.6.35.7 and dvb-t stick af9015.
The usb stick is fine determined, but mumudbv and scan not to works.

I write in terminal /system/xbin/scan/sdcard/dvbscan.conf
File not found
Also with the scan - # /system/xbin/mumudvb -c /sdcard/dvbscan.conf -d -v
File not found.

I understand it is necessary to put in some sort of library folder. Where to?

 

[hor13]

On UBUNTU 10.04 all configured!

This is my config for mumudvb:

freq=578
ip_http=127.0.0.1
port_http=8080
timeout_no_diff=130
dvr_buffer_size=5
#autoconf_radios=1

ip=127.0.0.1
unicast_port=8081
name=ORT
pids=101 102 103 104

ip=127.0.0.1
unicast_port=8082
name=Russia1
pids=201 202 203 204

ip=127.0.0.1
unicast_port=8083
name=NTV
pids=401 402 403 404

ip=127.0.0.1
unicast_port=8084
name=Russia_Culture
pids=601 602 603 604

ip=127.0.0.1
unicast_port=8085
name=Russia2
pids=301 302 303

ip=127.0.0.1
unicast_port=8086
name=5
pids=501 502 503

ip=127.0.0.1
unicast_port=8087
name=Russia24
pids=701 702 703

ip=127.0.0.1
unicast_port=8088
name=Karusel
pids=801 802 803

but the tablet gives the following: DEMUX DEVICE: /dev/dvb/adapter0/demux0 : No such file or directory
Although all of the folders and files exists:

/dev/dvb0.demux0
/dev/dvb/adapter0/demux0
/dev/dvb0.dvr0
/dev/dvb/adapter0/dvr0
/dev/dvb0.frontend0
/dev/dvb/adapter0/frontend0

what to do?

 

[klmn]

Hi, i have the IT913DBA DVB-T usb tuner and an 4.0.4 android tablet with 3.0.8+ kernel.
In the terminal insmod i see the error ''EXEC FORMAT ERROR''.How can i resolve it to isnmod the modules?
And how can install the firmware?

 

[BiOSsCZ]

Hello,
please please, someone handy who could compile the driver for Android devices

DVB-S2 FloppyDTV S2:

http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=a792cd12cf07cf77c7d1d41b46b4f8327ecf82d0
http://www.linuxtv.org/wiki/index.php/DVB-S2_IEEE1394_Devices

For any feedback I will be very grateful.
Have a nice day.

 

[Wild_eyed]

Is there a Forum Dedicated to the topic of DVB-T on Android?

i have some questions about getting it running on a JXD devce with af9015 based dongle.

looking for step by step guide really.

im not a noob but havent played with command line in ages.....