Android Tablets Forum banner
1 - 20 of 62 Posts

·
Premium Member
Joined
·
2,596 Posts
Discussion Starter · #4 ·
Used my fingernail to pry up the front by camera, then used my id which is stiff plastic and slid around the edges , while carefully applying upward pressure . and i do mean carefully, by the front charging port is the touch screen cable i got lucky it popped open with out breaking
 

·
Premium Member
Joined
·
334 Posts
So, there are no screws? The whole thing just snaps together? Can you get at the screen to remove it from the housing (I am looking to remove some dust). More pics of the top half possible - the screen/touch screen pic looks like the touch screen is turned over on the lid?
 

·
Premium Member
Joined
·
2,596 Posts
Discussion Starter · #6 ·
there are screws under closer examination, the size of eyeglass screws. I will have to remake the snaps so that it locks together . I will take more pics and post them of the lid
 

·
Premium Member
Joined
·
334 Posts
Thanks! You might want to take the opportunity to move the WIFI antena away from the battery, maybe into the open space around the speaker, then use a non metalic tape to hold it in place. Would probably improve signal strength!
 

·
Registered
Joined
·
87 Posts
[quote author=gevrik link=topic=521.msg4495#msg4495 date=1275523470]uh. what's up with that furtwangen advertisement link between those pics, which is full of wrong specs for the device?I hope you did not place it there on purpose?[/quote]This is my test device has no camera.
 

·
Registered
Joined
·
18 Posts
OK I tried to open my aPad. I used a guitar pick, and I found the easiest place to get it between the edges is next to the rocker (menu/home) switch, as the plastic flexes most there. I then used the pick and slid it round to the non-button end where it "popped" half open. What was happening was I was breaking the tiny screws out of their sockets. The black lining and plastic film are glued to the glass screen, and these screws are under the black edges. This isn't great news. What ever you do don't try and pull the film off the glass past the black edge, I now have a permanent "stretched glue crystal" corner in the top left on my screen. :(If you are going to do this, all you want is to carefully peel back the black plastic to expose the screws, and then I'll update you if I get any further.
 

·
Registered
Joined
·
18 Posts
Ok, I have found that heat does make the peeling process much easier. If you want to expose the screws you can use a hair dryer, and carefully pull the edges back.Now - does anyone know what I can do about the edge of my screen? All the stretched glue is left in the corner. What if I pulled the whole thing off, then used a solvent to remove the glue? Then I could stick it back on after I've done any modding required?
 

·
Registered
Joined
·
95 Posts
how time you can use the apad with wifi on???because its an only 3.7V??? 2500mAh 1000 more than the eken m001.Please give as the dimension of the battery, because we can use 2 or 3 in parallel for more mAhTHx
 

·
Premium Member
Joined
·
2,596 Posts
Discussion Starter · #16 ·
Let me reiterate , Be careful if you are going to open your apad. I can't say I would recommend it . send me your request and I will try to take better pics. I am def not a professional and for any one wondering it is a 10 megapixe camera that i am using.
 

·
Registered
Joined
·
103 Posts
[quote author=Handypaule link=topic=521.msg4444#msg4444 date=1275509006][quote author=xaueious link=topic=521.msg4434#msg4434 date=1275507352]Can we have more pictures, in higher resolution? We can't see much from that and it looks like you took it from a cellphone camera. [/quote]
[/quote]Tis seems to be not the APAD, it says M001 v2.0 on the board. I guess is the via chip one.
 

·
Premium Member
Joined
·
2,596 Posts
Discussion Starter · #18 ·
The is a much better pic
 

·
Premium Member
Joined
·
2,596 Posts
Discussion Starter · #20 ·
this is a rockchip slate, under the sticker it says Rockchip rk2808-1 7F44092 1017
 
1 - 20 of 62 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top