WonderMedia Technologies, Inc. W-Load Version : 0.15.00.01 UPDATE_ID_1_4_4_0_2_256MB_0150001 ethaddr............found wloader finish U-Boot 1.1.4 (May 12 2011 - 15:34:56) WonderMedia Technologies, Inc. U-Boot Version : UPDATEID_0.04.00.00.07 U-Boot code: 03F80000 -> 03FC2A30 BSS: -> 03FCCC4C boot from spi flash. SF0: ManufID = 1C, DeviceID = 3113 SF1: ManufID = 0, DeviceID = 0 (Missing or Unknown FLASH) Use Default - Total size = 8MB, Sector size = 64KB flash: Bank1: FFF80000 -- FFFFFFFF Bank2: FF780000 -- FFF7FFFF Flash: 8.5 MB sfboot NAND:env nand config fail, use default flash id list info pllb=0xc30, spec_clk=0x190a0fff T1=3, clk1=16, div1=7, Thold=1, tREA=25+delay(9) T2=2, clk2=18, div2=8, Thold2=1, comp=1 Tim1=524288 , Tim2=442368 T2=1, clk2=34, div2=15, Thold2=1, comp=1 Tim1=442368 , Tim2=557056 T2 is greater and not use T=2, clk=18, divisor=8, Thold=0x601 divisor is set 0x8, NFC_timing=0x2424 USE_HW_ECC ECC24bitPer1K 1 Nand flash found. Nand Flash Size: 2048 MB In: serial Out: serial Err: serial ### main_loop entered: bootdelay=1 logocmd="nandrw r ${wmt.nfc.mtd.u-boot-logo} ${wmt.display.logoaddr} 10000; nandrw r ${wmt.nfc.mtd.u-boot-logo2} ${wmt.display.logoaddr2} 40000; nandrw r ${" Load Image From NAND Flash col=0x2150, row = 0x3ff80 block2047 tag=42627430 version =1 col=0x2150, row = 0x3ff00 block2046 tag=31746242 version =1 bbt table is found USE_HW_ECC ECC24bitPer1K Read NAND Flash OK Load Image From NAND Flash USE_HW_ECC ECC24bitPer1K Read NAND Flash OK Load Image From NAND Flash USE_HW_ECC ECC24bitPer1K Read NAND Flash OK [VOUT] ext dev : LCD [VOUT] int dev : NO [LCD] wmt default lcd (id 4,bpp 24) vpp_config(800x480@60),pixclock 40000000 div_addr_offs=0x35c PLL_NO=1 [VPP] get base clock PLLC : 400000000 1div_addr_offs=0x374 PLL_NO=2 find the equal valuePLLN64, PLLD5, PLLP2, divisor2 freq=40000000Hz PLL0x5440, pll addr =0xd8130208 PLLN64, PLLD5, PLLP2, div2 div_addr_offs=0x374 read divisor=2, pll=0x5440 from register [GOVRH] set clock 40000000 ==> 40000000 div_addr_offs=0x374 PLL_NO=2 [VPP] get base clock PLLB : 40000000 vo_lcd_visible(1) ### main_loop: bootcmd="nandrw r ${kernel-NAND_ofs} 0x1000000 ${kernel-NAND_len}; if iminfo 0x1000000; then run kernelargs; bootm 0x1000000; fi; echo No ker" Hit any key to stop autoboot: 0 Initial SD/MMC Card OK! SD/MMC clock is 25Mhz register mmc device part_offset : 3d, cur_part : 1 part_offset : 3d, cur_part : 1 reading wmt_scriptcmd 249 bytes read ## Executing script at 00000000 ** Script length: 177 *E* lcd device 0 exist ! *E* lcd device 1 exist ! *E* lcd device 2 exist ! *E* lcd device 3 exist ! *E* lcd device 4 exist ! div_addr_offs=0x374 PLL_NO=2 [VPP] get base clock PLLB : 40000000 *W* vout mode register again 2 [VOUT] ext dev : LCD [VOUT] int dev : NO *W* vout mode register again 8 [LCD] wmt default lcd (id 4,bpp 24) vpp_config(800x480@60),pixclock 40000000 div_addr_offs=0x35c PLL_NO=1 [VPP] get base clock PLLC : 400000000 1div_addr_offs=0x374 PLL_NO=2 find the equal valuePLLN64, PLLD5, PLLP2, divisor2 freq=40000000Hz PLL0x5440, pll addr =0xd8130208 PLLN64, PLLD5, PLLP2, div2 div_addr_offs=0x374 read divisor=2, pll=0x5440 from register [GOVRH] set clock 40000000 ==> 40000000 div_addr_offs=0x374 PLL_NO=2 [VPP] get base clock PLLB : 40000000 vo_lcd_visible(1) Initial SD/MMC Card OK! SD/MMC clock is 25Mhz register mmc device part_offset : 3d, cur_part : 1 part_offset : 3d, cur_part : 1 reading uzImage.bin 3072136 bytes read ## Booting image at 00000000 ... Image Name: Linux-2.6.32.9-default Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3072072 Bytes = 2.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK No initrd ## Transferring control to Linux (at address 00008000) ... Starting kernel ... Uncompressing Linux.......................................................................................................................................... Linux version 2.6.32.9-default (hangyan@szmce12) (gcc version 4.5.1 (Sourcery G++ Lite 2010.09-50) ) #1 Wed Jul 13 09:56:43 HKT 2011 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: WMT Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 54356 Kernel command line: mem=214M root=/dev/mmcblk0p2 noinitrd rw rootfstype=ext2 console=ttyS0,115200n8 rootdelay=10 PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 214MB = 214MB total Memory: 210304KB available (5428K code, 1125K data, 148K init, 0K highmem) Hierarchical RCU implementation. NR_IRQS:128 Console: colour dummy device 80x30 console [ttyS0] enabled Calibrating delay loop... 348.97 BogoMIPS (lpj=1744896) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 wmt_pci_init PCI: WonderMidia Technology PCI Bridge PCI: bus0: Fast back to back transfers disabled [WMT-MB] Preparing VIDEO BUFFER (SIZE 32768 kB) ... [WMT-MB] MAX MB Area size: Max 4096 Kbs Min 256 Kbs [WMT-MB] prob /dev/Memory Block major 242, minor 0 bio: create slab at 0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. ashmem: initialized NTFS driver 2.1.29 [Flags: R/W]. JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. yaffs Jul 13 2011 09:56:24 Installing. msgmni has been set to 411 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) un-know id = 0x0 wmt sf controller initial ok Creating 6 MTD partitions on "mtdsf device": 0x000000000000-0x000000d00000 : "filesystem-SF" 0x000000d00000-0x000000f80000 : "kernel-SF" 0x000000f80000-0x000000fd0000 : "u-boot-SF" 0x000000fd0000-0x000000fe0000 : "u-boot env. cfg. 1-SF" 0x000000fe0000-0x000000ff0000 : "u-boot env. cfg. 2-SF" 0x000000ff0000-0x000001000000 : "w-load-SF" 1PMNAND_ADDR=0x8 kmalloc buffer env_ptr = 0xcd160000, env_ptr_nand = 0xcd160000 ## Warning: "wmt.io.nand" not defined NAND device: Manufacturer ID: 0xec, Chip ID: 0xd58472 (Samsung K9GAG08U0E) PLLB=0x10, spec_clk=0x190a0fff T1=2, clk1=17, div1=7, Thold=1, tREA=25+delay(9) T2=1, clk2=35, div2=14, Thold2=1, comp=1 Tim1=417792 , Tim2=573440 T2 is greater and not use T=2, clk=17, divisor=7, Thold=0x701 divisor PMNAND_ADDR is set 0x7, NFC_timing=0x2424 BCH ECC 24BIT ## Warning: "wmt.io.nand" not defined NAND device: Manufacturer ID: 0xec, Chip ID: 0xd58472 (Samsung K9GAG08U0E) find bbt page is 262016 find bbt page is 261888 WMT_nand: uboot no dynamic partitions defined, use default static Creating 11 MTD partitions on "WMT.nand": 0x000000000000-0x000000100000 : "w-load-NAND" 0x000000100000-0x000000a00000 : "u-boot env. cfg. 1-NAND" 0x000000a00000-0x000001300000 : "u-boot-NAND" 0x000001300000-0x000001b00000 : "kernel-NAND" 0x000001b00000-0x000002100000 : "initrd-NAND" 0x000002100000-0x000022100000 : "filesystem-NAND" 0x000022100000-0x000022500000 : "u-boot-logo" 0x000022500000-0x000022900000 : "kernel-logo" 0x000022900000-0x000042900000 : "android-data" 0x000042900000-0x00004a900000 : "android-cache" 0x00004a900000-0x000080000000 : "LocalDisk" nand initialised ok i2c /dev entries driver I2C PORT0: Transfer Mode = 1; Speed Mode = 1 i2c: adding wmt_i2c_adapter0. i2c: successfully added bus I2C PORT1: Transfer Mode = 1; Speed Mode = 1 i2c: adding wmt_i2c_adapter1. i2c: successfully added bus [wmt_i2c_api_i2c_init] [wmt_i2c_api_init] wmt_i2c_api_init. i2c: wmt algorithm module loaded. ## Warning: "wmt.display.direct_path" not defined vpp_init(boot logo 1) [VPP] GOVW TG 0,vpu en 0,vpu path 0 div_addr_offs=0x35c PLL_NO=1 [VPP] GOVW TG 0,vpu en 0,vpu path 0 [VPP] GOVW TG 1,vpu en 0,vpu path 0 [VPP] GOVW TG 1,vpu en 0,vpu path 0 [VO] vout_init: <1>vo_init_wm8435 vt1632 hw mode [VOUT] ext dev : DVI [VOUT] int dev : NO ## Warning: "wmt.display.user_res" not defined ## Warning: "wmt.display.regop" not defined [VOUT] param 2:0:16:0:0:0 [VOUT] boot parm vo LCD opt 0,16, 0x0@0 ## Warning: "wmt.display.param2" not defined ----------------------[VOUT] pwm 0:25:50:99 ------------------- [VOUT] blt 0,scalar 25,period 50,duty 99 [VOUT] tmr 40000:0:10:46:800:20:10:23:480:10 [VOUT] tmr pixclk 40000000,option 0x0,hsync 10,hbp 46,hpixel 800,hfp 20,vsync 10,vbp 23,vpixel 480,vfp 10 [VOUT] boot argument vo1 2,vo2 9 [VO] vo_boot_init: <7>vo_boot_init(0) vo_init_wm8440 (BOOT 800x480,0) gefb: framebuffer at 0f800000, mapped to d0000000, using 8192k, total 8192k Console: switching to colour frame buffer device 100x30 fb0: wmtfb frame buffer device loadtime = -3 start_boot_splash: screen xres = 800, yres = 480, info->var.bits_per_pixel =16 wmt.kernel.animation.addr = f600000, 0xf600000 map to 0xcda00000 [VO] vo_boot_config: <7>vo_boot_config [VO] vo_boot_config: <7>Exit vo_boot_config div_addr_offs=0x35c PLL_NO=1 [VPP] GOVW TG 0,vpu en 0,vpu path 0 [VPP] GOVW TG 1,vpu en 0,vpu path 0 [VPP] GOVW TG 1,vpu en 0,vpu path 0 fb1: WMT VPU frame buffer device Enter pwm_init mknod /dev/wmtgpio c 253 0 WMT vibrater driver load successfully! uart.0: ttyS0 at MMIO 0xd8200000 (irq = 32) is a wmt serial uart.1: ttyS1 at MMIO 0xd82b0000 (irq = 33) is a wmt serial WMT Serial driver initialized: ok brd: module loaded loop: module loaded nbd: registered device at major 43 pmem: 1 init PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 ## Warning: "wmt.io.mac.off" not defined VIA Rhine Family Fast Ethernet Adapter Driver Ver. 5.08 Copyright (c) 2002 VIA Technologies, Inc. eth0: VIA Rhine III Fast Ethernet Adapter eth0: MAC=00:40:63:10:94:51 IO=0xd8004000 Mem=0xd8004000 IRQ=10 usbcore: registered new interface driver asix Linux video capture interface: v2.00 WonderMedia CMOS camera register OK usbcore: registered new interface driver uvcvideo USB Video Class driver (v0.1.0) [wmt-vd] prob /dev/wmt-vd major 236, minor 0, prdt ffb1d000/d1e0000, size 100 KB [wmt-vd] WonderMedia HW decoder driver inited [wmt-lock] init ok, major=242, minor=1 get the cmos gpio setting : 1:0:7:0xd8110040:0xd8110080:0xd81100c0: Dean:spi_probe spi irq num = 0x18 B:0 A:8 spi_probe: /dev/WMT_SPI major number 153, minor number 0, device number 1 WMT EVB SPI Controlor Driver OK! uhci_hcd: USB Universal Host Controller Interface driver PCI: enabling device 0000:00:05.0 (0000 -> 0001) uhci_hcd 0000:00:05.0: UHCI Host Controller uhci_hcd 0000:00:05.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:05.0: detected 2 ports uhci_hcd 0000:00:05.0: irq 43, io base 0xd8007b00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: UHCI Host Controller usb usb1: Manufacturer: Linux 2.6.32.9-default uhci_hcd usb usb1: SerialNumber: 0000:00:05.0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected PCI: enabling device 0000:00:06.0 (0000 -> 0001) uhci_hcd 0000:00:06.0: UHCI Host Controller uhci_hcd 0000:00:06.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:06.0: detected 2 ports uhci_hcd 0000:00:06.0: irq 43, io base 0xd8008d00 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux 2.6.32.9-default uhci_hcd usb usb2: SerialNumber: 0000:00:06.0 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver cdc_acm cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial debug:1 by rubbitxiao USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems usbcore: registered new interface driver VIAUSBModem LinuxVIAUSBD1.0.4:VIA USB CDMA Modem USB Serial support registered for pl2303 usbcore: registered new interface driver pl2303 pl2303: Prolific PL2303 USB to serial adaptor driver USB Serial support registered for GobiSerial usbcore: registered new interface driver GobiSerial GobiSerial: 1.0.20 udc: VIA UDC driver, version: 3 December 2007 (dma) udc: pullup_disable() mount_thread udc: wmt_udc_probe - request_irq(0x2B) pass! mice: PS/2 mouse device common for all mice ## Warning: "wmt.io.ts" not defined ===== UTK Touch Disabled!===== p.x = 800, p.y = 480, gpio=2, irq=6 wmt.audio.i2s[i2sbus] not valid. set i2c-bus-1 input: VT1603 Touch Screen as /devices/virtual/input/input0 VT1603 Touch & Battery ADC Driver Installed!wmt_rtc on using rtc device, wmt-rtc, for alarms wmt-rtc wmt-rtc.0: rtc core: registered wmt-rtc as rtc0 WMT Real Time Clock driver v0.54 initialized: ok device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com device-mapper: multipath: version 1.1.0 loaded device-mapper: multipath round-robin: version 1.0.0 loaded device-mapper: multipath queue-length: version 0.1.0 loaded device-mapper: multipath service-time: version 0.2.0 loaded WMT ATSMB (AHB To SD/MMC Bus) controller registered! ## Warning: "rootdev" not defined Do not initialize mmc1 when boot from NandFlash. [MMC/SD driver] ATSMB1 probe Failed! sdmmc1: probe of sdmmc1.0 failed with error -22 ------------------ lcd_backlight_probe --------------- Registered led device: lcd-backlight usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver logger: created 256K log 'log_main' logger: created 256K log 'log_events' logger: created 64K log 'log_radio' Advanced Linux Sound Architecture Driver Version 1.0.21. No device for DAI VT1603 No device for DAI HWDEC i2c_transfer returned -5 WM8900 0-001b: Device is not a WM8900 - ID 0 ## Warning: "wmt.audio.echo.cancel" not defined WMT_SOC: dai_name=i2s, codec_name=vt1603 No device for DAI wmt-i2s-dai [VPP] set audio(fmt 16,rate 44100,ch 2) VT1603 Audio Codec 0.10 wmt.audio.i2s = vt1603:f1:f2:ff:ff:100 [i2sbus] invalid. set i2c_bus->1 [mic/linein] invalid. set record->mic playback volume percent[100%] ## Warning: "wmt.vt1603.debug" not defined ## Warning: "wmt.audio.fm34" not defined asoc: VT1603 <-> wmt-i2s-dai mapping ok ALSA device list: #0: WMT_SOC (VT1603) TCP cubic registered NET: Registered protocol family 17 lib80211: common routines for IEEE802.11 drivers ## Warning: "wmt.io.pwkey" not defined input: kpadPower as /devices/virtual/input/input1 [wmt_pm_init] battery_used = 3 PMC: WonderMedia Power Management driver PMC: Power button is configured as soft power [wmt_pm_init] power_on = 100 resume = 0 power_up = 500 registered taskstats version 1 wmt-rtc wmt-rtc.0: setting system clock to 2010-02-08 10:15:19 UTC (1265624119) mount_thread Waiting 10sec before mounting root device... mmc0: new high speed SDHC card at address e624 mmcblk0: mmc0:e624 SU04G 3.69 GiB mmcblk0: p1 p2 mmcblk0: p2 size 7688928 exceeds device capacity, limited to end of disk EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended VFS: Mounted root (ext2 filesystem) on device 179:2. Freeing init memory: 148K INIversion 2. Using makefile-style concurrent boot in runlevel S. procfile_write get 0 [Boot Animation] animation_stop FATAL: Module fbcon not found. [Boot Animation] animation_main thread finished Setting parameters of disc: (none). Checking root file system...fsck from util-linux-ng 2.17.2 /lib/init/rw/rootdev: The filesystem size (according to the superblock) is 961116 blocks The physical size of the device is 959524 blocks Either the superblock or the partition table is likely to be corrupt! /lib/init/rw/rootdev: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY. (i.e., without -a or -p options) fsck died with exit status 4 failed (code 4). An automatic file system check (fsck) of the root filesystem failed. A manual fsck must be performed, then the system restarted. The fsck should be performe! The root filesystem is currently mounted in read-only mode. A maintenance shell will now be started. After performing system maintenance, press CONTROL-D to. Give root password for maintenance (or type Control-D to continue): Login incorrect. Give root password for maintenance (or type Control-D to continue): �; CTRL-A Z for help |115200 8N1 | NOR | Minicom 2.4 | VT102 | Offline