[valkoz]

APPLICATION

Spoiler

ImageBurnTool – is a utility for low-level NAND formatting and mass installing firmware of the tablets with Amlogic CPU’s.

It allows:
- low-level NAND formatting (erase NAND) to exclude bad memory blocks
- mass install firmware for 8 tablets at the same time

REQUIREMENT OS: Windows XP 32/64-bit * Vista 32/64-bit * Windows 7 32/64-bit (see folder "_DRIVER", 32/64 bit drivers included)
REQUIREMENT OS: English or Chinese version of Windows - since version 1.6.2.0128 not necessarily
REQUIREMENT PC: According your OS

***********************

Amlogic Image Burning Tool v.1.6.2.0128 (2013-02-10)
Changes: allows to use non-English Windows

TOOL (see folder "_readme") Download: 16 mb
Google Disk https://docs.google....dit?usp=sharing
MediaFire http://www.mediafire...38wf9paai5q9c8d

MANUAL Download: 3 mb
Google Disk: https://docs.google....dit?usp=sharing
MediaFire: http://www.mediafire...kataafsywrcbfi8

How To: - FIRST OF ALL REMOVE EXTERNAL TF CARD ! FIRST OF ALL REMOVE EXTERNAL TF CARD ! FIRST OF ALL REMOVE EXTERNAL TF CARD !
 00.jpg (22.3K)
Number of downloads: 323->  01.jpg (143.29K)
Number of downloads: 365  02.jpg (110.45K)
Number of downloads: 332  03.jpg (87.49K)
Number of downloads: 288  04.jpg (80.59K)
Number of downloads: 278  05.jpg (80.27K)
Number of downloads: 270  06.jpg (82.59K)
Number of downloads: 267  07.jpg (92.05K)
Number of downloads: 266  08.jpg (76.92K)
Number of downloads: 273  09.jpg (88.82K)
Number of downloads: 272  10.jpg (94.16K)
Number of downloads: 273  11.jpg (98.65K)
Number of downloads: 274  12.jpg (105.71K)
Number of downloads: 273  13.jpg (82.8K)
Number of downloads: 285

ATTENTION !

In case you have error "cannot find disk! ..times" or "cannot load uImage ..times"

Decision:
1. press Stop
2. check point "erase nand"
3. press Start, wait until finished to erase
4. uncheck point "erase nand"
5. press Start to flash again

 15.jpg (134.56K)
Number of downloads: 239


RESQUE FIRMWARES for ONDA TABLETS

Spoiler

Purpose (use AML Flash Tool to flash from PC):
- to restore Bricked Tablet
- to facilitate the transition from ICS to JB

40D

Spoiler

More details here http://www.slatedroi...re/#entry657114 2 >>> How to upgrade from ICS to Jelly Bean
Download Resque Firmware 40D_resque
Size:81 mb
md5:6CBAC30192448B642E4C3C6BAC22BE10
GoogleDisk https://docs.google....dit?usp=sharing
MediaFire http://www.mediafire...xrr0lgld744uig0

971D

Spoiler

More details here http://www.slatedroi...re/#entry466606 2 >>> How to upgrade from ICS to Jelly Bean
Download Resque Firmware 971D_resque
Size:81 mb
md5:EEB589DB098669ACE62055BF16AA5CBC
GoogleDisk https://docs.google....dit?usp=sharing
MediaFire http://www.mediafire...6yexmzcfczrxr50

811D v.1-6

Spoiler

811D_resque (ICS based)
LINK: http://d-h.st/kZq

811D_resque_1tx (JB based) - in case you've message "can't load ... 30 times" in Amlogic Image Burning Tool
LINK: http://d-h.st/5IO

This post has been edited by valkoz: 19 May 2013 - 06:08 PM

[katana ixeon]

hey everybody, i need some help!?
i did flash my onda vi40DC with CM9 firmwear using SD Card method and the touch screen wouldn't work so i traid to flash it back using the same method but it wouldn't work to .so i tried to use AML Flash Tool but i tink that it didn't have WINDOW'S 7 32b Driver becaus the systeme codn't find the driver. please anybody help me !!
thanks

[valkoz]

katana ixeon, on 13 November 2012 - 07:27 AM, said:

hey everybody, i need some help!?
i did flash my onda vi40DC with CM9 firmwear using SD Card method and the touch screen wouldn't work so i traid to flash it back using the same method but it wouldn't work to .so i tried to use AML Flash Tool but i tink that it didn't have WINDOW'S 7 32b Driver becaus the systeme codn't find the driver. please anybody help me !!
thanks

Follow the path : USB-Burning-tool-SPI\_DRIVER_win7\ - it's enough for the AML Flash Tool

There are two drivers - 7 x 32 and 7 x 64 bit in the folders
/amd64 - 64 bit
/x86 - 32 bit

This post has been edited by valkoz: 13 November 2012 - 09:38 AM

[melbar79]

Hello Conner,

which modifications are need to avoid the installation via AML flash tool?

I know some guys, they install the org. V1.5.5 and the V2.0 for the Onda V711 with a european windows.
Causes many troubles...

In the future your jellybean custom roms will be available also with SD-card flash?

Thanks ,

melbar

[valkoz]

melbar79, on 13 November 2012 - 04:22 PM, said:

Hello Conner,

which modifications are need to avoid the installation via AML flash tool?

I know some guys, they install the org. V1.5.5 and the V2.0 for the Onda V711 with a european windows.
Causes many troubles...

In the future your jellybean custom roms will be available also with SD-card flash?

Thanks ,

melbar

Any of these custom roms http://www.slatedroi...ustom-firmware/ shall be flashed via SD-card (not PC, not AML flash tool)

Recommend v.1.4 or Hybrid firmware v.1.5-1.5.5

JB custom rom will be available also with SD-card flash

[melbar79]

I think you didn't understand me

If i download the original ROM (the V1.5.5 or the V2.0 when available) from Onda's website, then i'm forced to use the AML FLASH TOOL?!

And what do you do during the process 'org. ROM' --> 'custom ROM (in your words modded ROM )' to change from PC flash to SD flash?

[valkoz]

melbar79, on 14 November 2012 - 01:25 AM, said:

I think you didn't understand me

If i download the original ROM (the V1.5.5 or the V2.0 when available) from Onda's website, then i'm forced to use the AML FLASH TOOL?!

And what do you do during the process 'org. ROM' --> 'custom ROM (in your words modded ROM )' to change from PC flash to SD flash?

Yes, stock v.1.5.5 can be flashed from PC only

How to make rom to flash from SD - see attachment:

 SDflash.jpg (160.09K)
Number of downloads: 236

Connor

This post has been edited by valkoz: 14 November 2012 - 02:05 AM

[katana ixeon]

Hey everybody, i need help?!
I flash my Onda VI40 DC with CM9 and the teach screen wouldn't work, so i tried to flash it back with the stock flash but neither the SD Flash or USB Burning Tool method seem to work.
I'm asking if there is any other flashing program "with a working USB Driver" that i can use?
I did use "Livesuit" but I couldn't find any IMG Firmware for my device, so if there's a way to convert ZIP to IMG files, please let me know?
Thanx in advance....

[valkoz]

melbar79, on 13 November 2012 - 04:22 PM, said:

Hello Conner,

which modifications are need to avoid the installation via AML flash tool?

I know some guys, they install the org. V1.5.5 and the V2.0 for the Onda V711 with a european windows.
Causes many troubles...

In the future your jellybean custom roms will be available also with SD-card flash?

Thanks ,

melbar

Hi, melbar!

If you mean custom firmware - better to use ICS FINAL rom or v.1.5 hybrid or JELLY BEAN rom ('ll upload today) - all shall be flashed from SD card, not PC

For official firmware - any except v.1.5.5

Connor

katana ixeon, on 28 November 2012 - 02:14 PM, said:

Hey everybody, i need help?!
I flash my Onda VI40 DC with CM9 and the teach screen wouldn't work, so i tried to flash it back with the stock flash but neither the SD Flash or USB Burning Tool method seem to work.
I'm asking if there is any other flashing program "with a working USB Driver" that i can use?
I did use "Livesuit" but I couldn't find any IMG Firmware for my device, so if there's a way to convert ZIP to IMG files, please let me know?
Thanx in advance....

CM9 bootloader changed stock ONDA bootloader (recovery)

Better do the next:

1. use USB Burning Tool to erase nand - it works perennially

or skip 1. and

2. Flash from SD ICS FINAL rom or Jelly Bean custom

Livesuit doesn't works with Amlogic tablets (for A10 only)

Connor

This post has been edited by omarahum: 24 February 2013 - 06:52 AM

[gabrielrm]

Hi, could someone tell me how long it takes to erase nand, please?
I own an Onda V711 and it flashing success/disconnect for over an hour and don't know if is ok.
Thanks!

[valkoz]

gabrielrm, on 30 November 2012 - 09:29 AM, said:

Hi, could someone tell me how long it takes to erase nand, please?
I own an Onda V711 and it flashing success/disconnect for over an hour and don't know if is ok.
Thanks!

It takes less 3 sec. to erase nand usually.

To flash official firmware - about 2 min - but depend on how powerfull your pc is.

Connor

[gabrielrm]

Thank you for answering. I wasn't sure if erase was finish and didn't want to interrupt.
Now I think was silly question
Thank you again for your time, appreciated.

[dapa69]

Hi, i am new to this. I Have an Onda VI40 Dual - with original 4.03 firmware

I have flashed the new VI40D_v2.0-1129SD from a formatted SD card. All proceeded well until i read there were some errors. Now the Onda is sort of dead (the PC recognizes it as M3-CHIP). I can't start it or do anything else.

I have tried with the IMAGE BURN TOOL. All OK with the drivers etc (now the Onda is seen as worldcup device), but when i try to load the update.zip file (from the 1129SD), the tools says 'find no upgrade config please upload it manually' which stops me.

Any help. I have no clues anymore.

Thanks

[valkoz]

dapa69, on 08 December 2012 - 04:22 PM, said:

Hi, i am new to this. I Have an Onda VI40 Dual - with original 4.03 firmware

I have flashed the new VI40D_v2.0-1129SD from a formatted SD card. All proceeded well until i read there were some errors. Now the Onda is sort of dead (the PC recognizes it as M3-CHIP). I can't start it or do anything else.

I have tried with the IMAGE BURN TOOL. All OK with the drivers etc (now the Onda is seen as worldcup device), but when i try to load the update.zip file (from the 1129SD), the tools says 'find no upgrade config please upload it manually' which stops me.

Any help. I have no clues anymore.

Thanks

You need:
- unzip VI40D_v2.0-1129SD firmware to SD card and flash from SD card only! See: VI40D_v2.0-1129SD - means what firmware must be flashed from SD-card

Connor

[Simola]

dapa69, on 08 December 2012 - 04:22 PM, said:

Hi, i am new to this. I Have an Onda VI40 Dual - with original 4.03 firmware

I have flashed the new VI40D_v2.0-1129SD from a formatted SD card. All proceeded well until i read there were some errors. Now the Onda is sort of dead (the PC recognizes it as M3-CHIP). I can't start it or do anything else.

I have tried with the IMAGE BURN TOOL. All OK with the drivers etc (now the Onda is seen as worldcup device), but when i try to load the update.zip file (from the 1129SD), the tools says 'find no upgrade config please upload it manually' which stops me.

Any help. I have no clues anymore.

Thanks

Hi all, I think I've bricked my Onda
I tried to load the bootloader for upgrading to JB. I think I must have done something wrong as my tab now doesn't even boot to the white robot. The screen lights up as though it's booting but does nothing.

I'm trying to re-flash using AML Flash Tool but I get 'find no upgrade config please upload it manually' and can't get any further. I've tried flashing all the ROM's I can get my hands on but get the same result every time.

Can anyone help please? Thanks.

This post has been edited by Simola: 12 December 2012 - 06:01 PM

[valkoz]

Simola, on 12 December 2012 - 06:00 PM, said:

Hi all, I think I've bricked my Onda
I tried to load the bootloader for upgrading to JB. I think I must have done something wrong as my tab now doesn't even boot to the white robot. The screen lights up as though it's booting but does nothing.

I'm trying to re-flash using AML Flash Tool but I get 'find no upgrade config please upload it manually' and can't get any further. I've tried flashing all the ROM's I can get my hands on but get the same result every time.

Can anyone help please? Thanks.

Guys, DO NOT TRY TO USE AML FLASH TOOL to flash JB firmwares!

JB firmware for SD flash only!

It's impossible to kill tablet by stock firmware.

In your case may help http://www.slatedroi.../41380-jb-roms/ - How to flash ROM Step 1. Preparing new bootloader for JB

or

simply flash that http://www.slatedroi...-ics-rom-final/

Connor

This post has been edited by valkoz: 12 December 2012 - 10:49 PM

[Simola]

valkoz, on 12 December 2012 - 10:44 PM, said:

Guys, DO NOT TRY TO USE AML FLASH TOOL to flash JB firmwares!

JB firmware for SD flash only!

It's impossible to kill tablet by stock firmware.

In your case may help http://www.slatedroi.../41380-jb-roms/ - How to flash ROM Step 1. Preparing new bootloader for JB

or

simply flash that http://www.slatedroi...-ics-rom-final/

Connor

Thanks Connor, I dont think I was clear. I tried to flash the bootloader using SD card method. It didn't seem to work...doesn't even boot to white robot. When I turn the tab on the screen brightens but stays black.....no further response at all. Is there anyway to recover tablet? I've tried rescue disk but as tab doesnt boot to white robot I don't know what to do. Thanks for your help.

[valkoz]

Simola, on 13 December 2012 - 05:18 AM, said:

Thanks Connor, I dont think I was clear. I tried to flash the bootloader using SD card method. It didn't seem to work...doesn't even boot to white robot. When I turn the tab on the screen brightens but stays black.....no further response at all. Is there anyway to recover tablet? I've tried rescue disk but as tab doesnt boot to white robot I don't know what to do. Thanks for your help.

It's ok.

If white robot doesn't appears, but display is dim when power on - try next:

- power off tablet

- flash ICS FINAL rom (today evening I'll upload v. EN03)

It must work - I make so very often.

(when use rescue disk or try to flash JB first time, white robot doesn't appears after second power on. Rollback to ICS shall help always)

PS. Time period between dim display and Green robot is about 15-20 sec., hold HOME button on.

Connor

This post has been edited by valkoz: 16 December 2012 - 05:16 AM

[Simola]

valkoz, on 16 December 2012 - 04:53 AM, said:

It's ok.

If white robot doesn't appears, but display is dim when power on - try next:

- power off tablet

- flash ICS FINAL rom (today evening I'll upload v. EN03)

It must work - I make so very often.

(when use rescue disk or try to flash JB first time, white robot doesn't appears after second power on. Rollback to ICS shall help always)

PS. Time period between dim display and Green robot is about 15-20 sec., hold HOME button on.

Connor

Hi Connor,

Thank you...but I still can't get the tablet to boot.

You say to turn off tablet and flash ICS FINAL rom. How do I do this if the tablet won't even boot to white robot?

I've tried holding home and then powering on but this doesn't go to Green robot, even after 15-20 secs.

All that happens when I press the on button is the screen brightens slightly and stays bright for 5 seconds and then goes off again.

If there's anymore help you can offer that would be appreciated.

Thanks

[evertoexcel]

Simola, on 17 December 2012 - 04:40 PM, said:

Hi Connor,

Thank you...but I still can't get the tablet to boot.

You say to turn off tablet and flash ICS FINAL rom. How do I do this if the tablet won't even boot to white robot?

I've tried holding home and then powering on but this doesn't go to Green robot, even after 15-20 secs.

All that happens when I press the on button is the screen brightens slightly and stays bright for 5 seconds and then goes off again.

If there's anymore help you can offer that would be appreciated.

Thanks

Hi,

I had the same situation like you after I tried to load the bootloader (JB ROM, Step1). Only way I could go back is to load the ICS Final rom, strange thing was that when I holding home and then powering...There was no white robot, after waiting sometimes it went straight to green robot! And then eventually it loaded ICS Final as usual.